Solid
ifaces/battery.h
BatteryType
This enum type defines the type of the device holding the battery.
Definition frontend/battery.h:71
This device interface is available on batteries.
Definition ifaces/battery.h:23
virtual void capacityChanged(int value, const QString &udi)=0
This signal is emitted when the capacity of this battery has changed.
virtual Solid::Battery::Technology technology() const =0
Retrieves the technology used to manufacture the battery.
virtual void timeToFullChanged(qlonglong time, const QString &udi)=0
This signal is emitted when the time until the battery is full has changed.
virtual void energyFullDesignChanged(double energy, const QString &udi)=0
This signal is emitted when the energy full design value of this battery has changed.
virtual void voltageChanged(double voltage, const QString &udi)=0
This signal is emitted when the voltage in the cell has changed.
virtual double energyFull() const =0
Amount of energy (measured in Wh) the battery has when it is full.
virtual void energyFullChanged(double energy, const QString &udi)=0
This signal is emitted when the energy full value of this battery has changed.
virtual double energyFullDesign() const =0
Amount of energy (measured in Wh) the battery should have by design hen it is full.
virtual void chargeStateChanged(int newState, const QString &udi=QString())=0
This signal is emitted when the charge state of this battery has changed.
virtual void powerSupplyStateChanged(bool newState, const QString &udi)=0
This signal is emitted when the power supply state of the battery changes.
virtual void temperatureChanged(double temperature, const QString &udi)=0
This signal is emitted when the battery temperature has changed.
virtual int capacity() const =0
Retrieves the battery capacity normalised to percent, meaning how much energy can it hold compared to...
virtual void remainingTimeChanged(qlonglong time, const QString &udi)=0
This signal is emitted when the estimated battery remaining time changes.
virtual void chargePercentChanged(int value, const QString &udi)=0
This signal is emitted when the charge percent value of this battery has changed.
virtual int chargePercent() const =0
Retrieves the current charge level of the battery normalised to percent.
virtual qlonglong timeToFull() const =0
Time (in seconds) until the battery is full.
virtual void energyChanged(double energy, const QString &udi)=0
This signal is emitted when the energy value of this battery has changed.
virtual Solid::Battery::BatteryType type() const =0
Retrieves the type of device holding this battery.
virtual bool isRechargeable() const =0
Indicates if the battery is rechargeable.
virtual double energy() const =0
Amount of energy (measured in Wh) currently available in the power source.
virtual int cycleCount() const =0
Retrieves the number of charge cycles this battery has experienced so far, or -1 if this information ...
virtual qlonglong timeToEmpty() const =0
Time (in seconds) until the battery is empty.
virtual double voltage() const =0
Voltage in the Cell or being recorded by the meter.
virtual bool isPowerSupply() const =0
Indicates if the battery is powering the machine.
virtual double temperature() const =0
The temperature of the battery in degrees Celsius.
virtual double energyRate() const =0
Amount of energy being drained from the source, measured in W.
virtual void cycleCountChanged(int value, const QString &udi)=0
This signal is emitted when the number of charge cycles of the battery has changed.
virtual bool isPresent() const =0
Indicates if this battery is currently present in its bay.
virtual qlonglong remainingTime() const =0
Retrieves the current estimated remaining time of the system batteries.
virtual void energyRateChanged(double energyRate, const QString &udi)=0
This signal is emitted when the energy rate value of this battery has changed.
virtual void timeToEmptyChanged(qlonglong time, const QString &udi)=0
This signal is emitted when the time until the battery is empty has changed.
virtual void presentStateChanged(bool newState, const QString &udi)=0
This signal is emitted if the battery gets plugged in/out of the battery bay.
virtual Solid::Battery::ChargeState chargeState() const =0
Retrieves the current charge state of the battery.
Base interface of all the device interfaces.
Definition ifaces/deviceinterface.h:23
This file is part of the KDE documentation.
Documentation copyright © 1996-2024 The KDE developers.
Generated on Sat Dec 21 2024 17:03:23 by doxygen 1.12.0 written by Dimitri van Heesch, © 1997-2006
Documentation copyright © 1996-2024 The KDE developers.
Generated on Sat Dec 21 2024 17:03:23 by doxygen 1.12.0 written by Dimitri van Heesch, © 1997-2006
KDE's Doxygen guidelines are available online.